1404 cfm cooler pad system manual#
1404 cfm cooler pad system code#
1404 cfm cooler pad system series#

The secondaryвЂ™s open faster, meaning they open with less vacuum drop than with the stock set-up. I removed the secondary counterweights and drilled 3/8вЂќ diameter holes in them.

The tub-type bowls and rear-pivot floats all contribute to a carburetor that is reliable, user-friendly and is easily tuned for trouble-free operation. The all-aluminum body is compatible with gasohol and blended fuels, and features a two piece body that resists warping. This means that compared to other carburetors the performance remains consistent and the calibration stays unchanged. They have the unique ability to вЂњhold a tuneвЂќ, so once theyвЂ™re tuned, they stay tuned. This means there are no power valves to blow out the rods can be changed in seconds, without carburetor removal or fuel draining. They use metering rods to transition between circuits, and are unaffected by engine backfires. Several characteristics make Edelbrock carburetors outstanding street performers. One item I neglected was the advantages an Edelbrock has over its competition. Last month I wrote about the set-up and tuning of the Edelbrock carburetor. All the kits include one pair of metering rod retaining springs, five pair of step-up springs, and a specified number of rod pairs and jet pairs, depending on the size carburetor being used.

They could, however, cause higher hydrocarbon emissions and tend to foul spark plugs.Д¬alibration kits are available to change the metering jets and rods to suit different operating conditions or engine combinations. Settings richer than this will not improve idle quality or performance. Go leaner just enough to get a 20 RPM drop in speed.

Carefully trim each idle mixture screw to again get the maximum idle speed or vacuum reading.Obtain maximum speed or vacuum reading for this screw. Adjust the screw opposite the side just done.If the above procedure changed the idle speed more than 40 RPM, readjust the idle speed.Adjust the idle mixture screw on one side to get the maximum possible RPM or highest vacuum reading.Set the desired idle speed with the idle speed screw.Fully warm the motor so the choke is fully open.Remember, we are looking for the best vacuum reading possible at a set idle speed. This is rich, but will give a baseline for further adjustments. Set the idle mixture screws two turns out from bottom as a starting point. To set the proper idle mixture adjustment, follow these directions: The carburetor comes with primary metering jets of 0.086вЂќ, secondary jets of 0.095вЂќ metering rods are 0.065вЂќ x 0.052вЂќ. Go to for a chart of carburetor applications and specifications. Above 400 cubic inches you should use a dual quad set-up.

1404 cfm cooler pad system manual#

The 1404 is a 500 CFM manual choke, non-EGR model recommended for small cubic inch stock motors small is 400 cubic inch or lower. It could probably use a rebuild at this point, since all the components are 10 years old, and the car sits for a good part of the year. I have had the model #1404 installed in my car (MKI, stock 260 motor) for 10 years and have never had to make adjustments. I have mounted a vacuum gauge in my Tiger in the hole that used to house the clock so I can check the vacuum at a glance. The optimum setting is the leanest possible ratio to give maximum vacuum pressure at idle RPM.ДЄ vacuum gauge can be used to properly set the carb idle speed, or it can be done with a tachometer, or both. Turning these screws out gives a rich mix, in yields a lean mix. Setting the idle mixture is done by turning two screws located at the front of the carb. The correct idle mixture is essential for smooth idling as well as to create a seamless transition to open throttle operation.

1404 cfm cooler pad system code#

The carb part number is stamped on the pad at the front of the carb after the four digit manufacturing code number. The 800 CFM units are for high performance street/light strip use. The #1409 600 CFM and #1410 750 CFM units are marine applications. Manual or electric choke options are available.

1404 cfm cooler pad system series#

The Edelbrock Performer Series carburetors are a redesigned Carter unit that gives near electronic fuel injection economy while maintaining wide open throttle performance. By Fred Baum in the May and June 2006 RootesReview:ДЄbout ten years ago I gave up on my Holley 4-barrel carburetor and purchased an Edelbrock four-barrel.